The core logic of a stop-snoring pillow is simple: detect snoring or head movement → trigger mechanical feedback (НАПРИМЕР., inflation/vibration) → allow the user to turn over or adjust posture. Однако, the selection of датчики to realize this logic requires engineers to speak in terms of parameters and physical quantities, rather than something nebulous. Here are the key functional requirements and corresponding parameter configurations, directly on the conclusion:
Давайте начнем понимать!
Каталог
Sensor Functional Requirements
Snoring Detection:
Need to capture low-frequency vibration (20-200Гц) and sound signals.
Head position monitoring:
To determine whether the user is lying on his/her back (high risk position for snoring).
Anti-interference ability:
Filtering environmental noise (such as mattress shaking, turning movements).
Заключение:
Required three-piece set-MEMS microphone, three-axis accelerometer, pressure sensor.
Parameter configuration: reject fuzzy descriptions, quantize to the decimal point
1. MEMS microphone (snoring detection)
- Range: ≥ 100dB SPL (covering snoring sound pressure level 50-90dB).
- Frequency Response: 20Hz-1kHz (snoring main frequency band).
- Signal-to-noise ratio (SNR): ≥ 64dB (to avoid false triggering by environmental noise).
- Рабочее напряжение: 1.8V-3.6V (compatible with low-power MCU).
Why?
- Snoring is a low-frequency, high-energy signal, but may be interfered with by air conditioning and breathing airflow. High SNR ensures effective separation of target signals.
Triaxial Accelerometer (Head Position Monitoring)
- Range: ± 2g (sufficient to cover micro-movements of the head and prevent saturation).
- Resolution: ≤ 1mg/LSB (detects small inclination changes in supine/side-lying).
- Точность: ± 2% FSR (full scale error to avoid postural misjudgment)
- Диапазон температур: -20°C ~ 70°C (covers extreme storage environments).
Why?
- Too large a range (например. ±8g) will reduce the resolution, while the pillow action itself is a low-frequency micro-movement, ±2g is sufficient. Temperature range needs to be considered for storage and transportation scenarios.
- Range: 0-40кПа (head static pressure usually <10кПа).
- Линейность: ± 0.5% FSR (pressure distribution consistency requirements).
- Время ответа: ≤ 10ms (real-time feedback requirements)
- Рабочее напряжение: 5V or 3.3V (compatible with mainstream power supply program).
Why?
- Excessive range (например. 100кПа) will sacrifice accuracy, while the dynamic range of head pressure is limited, 40kPa is sufficient margin.
Hidden Details
Потребляемая мощность:
Sensor standby current must be ≤ 10μA, otherwise the battery power will not last a week.
Interface:
I²C or SPI digital output is preferred, ADC solution will increase the burden of MCU.
Calibration:
Accelerometers and pressure sensors need to be factory calibrated, manual zeroing by the user is not possible.
EMC:
Pillow may be close to cell phone/WiFi router, sensors need to pass EMI test.
Balance between cost and performance
Low cost solution:
use analog microphone + low precision accelerometer (error ±5%), cost down to $1.5, but false trigger rate >10%.
Reliable solution:
digital MEMS microphone + automotive grade accelerometer (например. Bosch BMA456), cost $3-4, false trigger rate <3%.
Engineer advice:
don’t save money on sensors! After-sales complaints and return costs are much higher than hardware BOM difference.
IP Rating
Recommended rating: IP54 and above
- Sweating is inevitable during sleep, so the sensor needs to be waterproof.
- The dustproof rating is to extend the service life of the sensor.
Заключение
| Sensor Type | Core Parameters | Recommended Models |
|---|---|---|
| MEMS Microphone | SNR≥64dB, 100dB SPL | InvenSense ICS-43434 |
| Accelerometer | ±2g, 1mg resolution | ST LIS2DH12 |
| Pressure sensor | 40кПа, ±0.5% linearity | Tekscan FlexiForce A201 |
Примечание: Be sure to actually test the pillow + mattress + human body coupling scene after selection, laboratory data ≠ real effect!
The last big truth:
the technical threshold of anti-snoring pillow is not in the sensor itself, but in the signal processing algorithm (how to distinguish between snoring and farting). Однако, if the sensor parameters are not up to standard, the algorithm will not be able to save it even if it is awesome.
To design a truly effective stop snoring pillow, the configuration of the sensor must not be sloppy. From range and accuracy to power consumption and output interface, every parameter needs to be rigorously evaluated and verified. Only by doing the best in technical details can we truly realize the promise of “black technology to stop snoring” in the market.
For engineers, choosing the right sensor is not only the key to the success of the product, but also the core competitiveness to enhance the user experience. We hope that this technical guide can provide you with some practical references on the road of development of anti-snoring pillow.
